A recent news has aroused everyone's concern: "Shenzhen traffic police has begun to install mobile bus electronic police in front of the city's bus front windshield, based on video surveillance, the use of models, yellow line recognition, GPS positioning and other algorithms, real-time traffic through 3G wireless map transmission Illegal shots. If illegally occupied bus lanes are used, a fine of 300 yuan will be imposed; if a bus stops illegally at a bus stop, a fine of 1,000 yuan shall be imposed." It was true that the car was on the road to “crisis†and many car owners had suffered a lot of losses. Can everyone clearly understand what the meaning of the various vertical and horizontal markings on the road is? Also know what can be suppressed and which can not be suppressed? Do you know what kind of punishment will be caused if you do not follow the instructions of these signs? This article will give you a solution.
What happens when the pressure line is violated?
We often say that the “crimes on the press line†is the correct name in the traffic regulations is “violation of the prohibition of marking instructionsâ€, mainly the following situations:
1. The single and double solid lines all belong to the prohibition of marking. During the driving process, the pressure line and the line are all illegal;
2. Crossroads do not follow the guide markings in the corresponding lanes;
3. Temporary or long-term parking in the banned area;
The ones that are caught are very simple: demerit points and fines, but different cities have different penalties. The penalties are different, some are not fines, and some are fines + deductions, but they are all illegal. behavior.
-------------------------------------
Which lines cannot be pressed?
1. Solid line (double yellow solid line & single yellow solid line & white solid line)
The main purpose of the solid line is to prohibit bi-directional vehicles from crossing or pressing. Single/double solid lines are generally set in one direction with one or two or more than two motor lanes; the role of the solid white line is to separate the same direction. Lanes are usually set up before intersections with traffic lights. These three are often tricked by owners.
2, yellow / white virtual line
In the ramp, turn, turn, vehicle entrance, etc. often appear white or yellow virtual solid line, the vehicle on the side of the dotted line can change lanes or turn, and the vehicle on the side of the solid line can only follow the lane, the car is mainly careful Don't make mistakes.
3, diversion line & yellow prohibited line
The area of ​​these two types of markings is very large, so many owners who do not understand are mistaken for parking areas. Diversion lines generally appear at intersections, ramps, etc., to guide the vehicles to follow the prescribed routes; the prohibition lines are mostly yellow mesh stripes, which generally appear in the units and school gates, and the marked areas are prohibited from parking. So the owners don't see a large empty stop.
4, guide marking
This is also one of the most common “projects†for most car owners. This should be the simplest road marking, indicating that the vehicles are on the way. However, sometimes owners may rush through the intersection for convenience or some are not familiar with the intersection. It caused violations. At the same time, this type of violation is also the highest probability of being caught. Fine penalty points are unavoidable because most of them are at the traffic lights. Therefore, when driving, the owner must pay attention to selecting the road in advance and avoid making mistakes.
5, special lane
Bus lane lanes, as their name suggests, are used to drive specific vehicles, such as bus lanes, non-motorized lanes, etc. However, some drivers simply go to a dedicated lane for convenience. If a vehicle enters a special lane illegally, it is illegal if it is violated. Shooting or catching it can only be punished.
What other markings need attention?
1, turn left to turn area
Most of the cities in the left-turning waiting-to-transition area have to turn left-turning vehicles to wait in order to increase the traffic volume of vehicles and avoid traffic jams, so that the left-turn car will wait first, but if the lights are both in the straight ahead and the left turn lights are turning The district is calculated according to the red light, so owners need to pay attention when they encounter this kind of road.
2, deceleration prompt marking
Deceleration prompts marked on the road often appear on a large area of ​​the prompt signs, which in fact remind the vehicle deceleration markings or logos, often appear in the expressway, highway, schools around, intersections and so on. Various styles and rich, there are three-dimensional patterns, graphic patterns.
3, digital marking
Speed ​​Marking The urban expressway will be marked with large numbers on the ground. This is the requirement for the speed of the driving lane. It is generally divided into white and yellow. The white number indicates the minimum speed limit of the road section, and the yellow number indicates the maximum speed limit.
Conclusion: There are various types of markings on the road, and there are no direct signs without traffic signs. If you do not understand clearly and can be “pitted†at any time, then the penalty or demerit points will be unavoidable. Therefore, owners, especially novice owners, should be familiar with various traffic markings to save money for themselves, and second, to develop safe driving habits.
The manipulator is the core of the automatic welding manchinery which is composed of kinds of welding rectifier, Hanging Welding Head, Welding Turning Rolls, Welding Positioner, welding fluid feed-in and recovery system and so on. It is a whole set of welding equipment that can be used for metal pressuer vessel and metal machinery. The autoization Welding Machinery is widely used in pressure vessel, refrigeration plant, power plant, wind tower generating equipment, aviation, metallurgy industry, engineering plant, watercraft manufacture, roller resurfacing welding, petrochemical industry and so on.
CZ22-7×7 Complete Equipment of Spherical Head Welding Center
Spherical automatic welding plane is a cross Welding Machine , a set of ESAB wire submerged arc welding system, a set of ESAB with submerged arc welding system, a set of double column welding positioner.
Spherical welding center equipment mainly by the operating machine, ESAB welding system; TV monitoring system; flux feed recovery system, electrical control system, up and down tracking system, with a very surfacing institutions, water cooling system and other components.
The main technical parameters
|
Name |
Details parameters |
|
|
1 |
Power supply |
|
|
2 |
Vertical load |
MAX 50t |
|
3 |
The workpiece weighs 50 tons and supports the diameter 1600mm-6000mm |
When the working conditions for the horizontal position forward 90 °, in the 50 tons load, the workpiece center of gravity from the position of the machine table plane distance of up to 1000mm |
|
4 |
Artifacts eccentricity |
In the 50 tons load, the workpiece center of gravity from the position of the machine table axis up to 300mm |
|
5 |
Spinning speed |
0,015 – 0.25 rpm |
|
6 |
Rotation rate change rate |
≤5% |
|
7 |
Flip speed |
0,01-0,15rpm |
|
8 |
±180°(double-seater) |
|
|
9 |
Worktable diameter |
Ф 6000mm |
|
10 |
The workbench to adjust height |
600mm |
|
11 |
Maximum welding current |
3000A |
|
12 |
Maximum preheat temperature |
400℃ |
|
13 |
≥ 24h |
We can provide the whole set welding manchinery for worldwide customers with high quality and good service, which is designed, manufactured, installed by ourselves.
Welding Machinery
Welding Machinery,Saw Welding Machine,Automatic Welding Machine,Machinery For Welding Metal
SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachine.com