1. Preparation before operation (1) The rear part of the sewage suction truck should be as close as possible to the operating point and parked.
(2) Pull the return oil tank's straight cock rotating handle to the angle of about 45° with the axis of the oil inlet pipe. Observe the oil inlet pipe and there should be lubricating oil flow.
(3) Open the side door of the walk-in box and take out the dirt-absorbing rubber hose so that it swings back without bending.
2. Suction work (1). Draw the dirt-contaminated hose as deep as possible to ensure that the end of the pipe is 300mm or less from the liquid surface during the work process.
(2) Push the four-way valve handle vertically to the ground.
(3). Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, and the vacuum pump starts to run.
(4) Open the cabin tool box, pull out the alarm switch, and turn it on.
(5) The operator can pass through the observation mirror on the upper part of the rear head. When the liquid level reaches the middle of the observation mirror, the operator should be notified that the colleague should quickly pull the suction hose away from the ground or close the four-way valve. Under normal circumstances, the sounder will emit audible and visual signals at this time. When the driver receives the signal, the throttle should be reduced. The power take-off switch is pushed forward and the gear is removed. The vacuum pump stops moving and presses the switch to cut off the power. .
(6) Close the fuel tank straight cock rotating handle plate parallel to the axis of the incoming mailbox.
(7) After flushing the hose, place it back in the walkway box, close the side door, and position the boom over the cab.
(8) Close the anti-overflow valve so that the handle is perpendicular to the axis of the road.
(9) Drive the sewer truck away from the operating point.
3. Draining operation (1) Put the suction hose toward the storage tank.
(2) Pull the rear handle of the four-way valve parallel to the ground and open the spill-proof valve so that the handle and the pipe axis can be parallel.
(3) Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, take the power, start the vacuum pump, put the transmission into neutral, then start the engine, disconnect the clutch, turn the power take off switch Pull backwards to pull the file, and the vacuum pump starts to operate.
(4) After the discharge of the liquid in the tank, the driver should push the power take-off handle forward and remove the gear, and the vacuum pump stops running.
(5) Close the fuel tank straight cock rotating handle plate and enter the axis of the e-mail box and close it. After the hose is rinsed, put it back into the walk-in box, close the side door, and make the suspender point towards the cab.
(6) Move the sewer truck away from the operating point.
Sewage suction car precautions (1) to maintain the appropriate number of vacuum pump speed Vacuum pump speed is too high, the rotor heating plus data; speed is too low, it will cause additional impact on the shipping machine, components, affecting life. In order to achieve a suitable working speed, please adjust the best position of the hand throttle in advance according to the pump type.
(2) Self-unloading cans on flat ground;
The unloading of the tank on an inclined road surface will cause distortion of the components and cause failures, and it may cause roll-over accidents.
(3) Open the tank after the unloading can open the tank door:
Before releasing the mud from the unloading tank, the locking bolt should be loosened and the rear tank door should be lifted to the required angle. When the tank is full, it is forbidden to lift the tank body with the rear tank door closed. Otherwise, there is a risk of overturning.
(4) When the oil pump and the vacuum pump take power, the engine idles and the clutch pedal is fully depressed. After the power take-off switch is turned on, slowly release the clutch pedal.
(5) The vacuum pump and the oil pump are stopped when the car is running.
(6) The vehicle must not inhale material larger than the diameter of the hose and transport waste oil and hazardous materials.
(7) Support rods and safety stops must be used when the unloading tank is lifted into the bottom of the tank or during overhaul.
(8) When transporting dirt, the vehicle must be driven at a moderate speed and at a slow speed, and no sharp turning or sudden braking should be allowed because the center of gravity of the anti-wave board is not high.
Shenzhen Rongdian Printing Products Co., Ltd. is located at 303, 3rd Floor, Building 2, Potoudu Industrial Zone, Longxi Village, Longcheng Street, Longgang District, Shenzhen, Guangdong Province, China. It mainly deals in various printing products: stickers, product color boxes, exquisite gift boxes, picture albums , Promotional color pages, trademark tags, envelope receipts! Shenzhen Rongdian Printing Products Co., Ltd. adheres to the production philosophy of "printing every product with heart" and strictly implements it! Looking forward to your visit~
(2) Pull the return oil tank's straight cock rotating handle to the angle of about 45° with the axis of the oil inlet pipe. Observe the oil inlet pipe and there should be lubricating oil flow.
(3) Open the side door of the walk-in box and take out the dirt-absorbing rubber hose so that it swings back without bending.
2. Suction work (1). Draw the dirt-contaminated hose as deep as possible to ensure that the end of the pipe is 300mm or less from the liquid surface during the work process.
(2) Push the four-way valve handle vertically to the ground.
(3). Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, and the vacuum pump starts to run.
(4) Open the cabin tool box, pull out the alarm switch, and turn it on.
(5) The operator can pass through the observation mirror on the upper part of the rear head. When the liquid level reaches the middle of the observation mirror, the operator should be notified that the colleague should quickly pull the suction hose away from the ground or close the four-way valve. Under normal circumstances, the sounder will emit audible and visual signals at this time. When the driver receives the signal, the throttle should be reduced. The power take-off switch is pushed forward and the gear is removed. The vacuum pump stops moving and presses the switch to cut off the power. .
(6) Close the fuel tank straight cock rotating handle plate parallel to the axis of the incoming mailbox.
(7) After flushing the hose, place it back in the walkway box, close the side door, and position the boom over the cab.
(8) Close the anti-overflow valve so that the handle is perpendicular to the axis of the road.
(9) Drive the sewer truck away from the operating point.
3. Draining operation (1) Put the suction hose toward the storage tank.
(2) Pull the rear handle of the four-way valve parallel to the ground and open the spill-proof valve so that the handle and the pipe axis can be parallel.
(3) Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, take the power, start the vacuum pump, put the transmission into neutral, then start the engine, disconnect the clutch, turn the power take off switch Pull backwards to pull the file, and the vacuum pump starts to operate.
(4) After the discharge of the liquid in the tank, the driver should push the power take-off handle forward and remove the gear, and the vacuum pump stops running.
(5) Close the fuel tank straight cock rotating handle plate and enter the axis of the e-mail box and close it. After the hose is rinsed, put it back into the walk-in box, close the side door, and make the suspender point towards the cab.
(6) Move the sewer truck away from the operating point.
Sewage suction car precautions (1) to maintain the appropriate number of vacuum pump speed Vacuum pump speed is too high, the rotor heating plus data; speed is too low, it will cause additional impact on the shipping machine, components, affecting life. In order to achieve a suitable working speed, please adjust the best position of the hand throttle in advance according to the pump type.
(2) Self-unloading cans on flat ground;
The unloading of the tank on an inclined road surface will cause distortion of the components and cause failures, and it may cause roll-over accidents.
(3) Open the tank after the unloading can open the tank door:
Before releasing the mud from the unloading tank, the locking bolt should be loosened and the rear tank door should be lifted to the required angle. When the tank is full, it is forbidden to lift the tank body with the rear tank door closed. Otherwise, there is a risk of overturning.
(4) When the oil pump and the vacuum pump take power, the engine idles and the clutch pedal is fully depressed. After the power take-off switch is turned on, slowly release the clutch pedal.
(5) The vacuum pump and the oil pump are stopped when the car is running.
(6) The vehicle must not inhale material larger than the diameter of the hose and transport waste oil and hazardous materials.
(7) Support rods and safety stops must be used when the unloading tank is lifted into the bottom of the tank or during overhaul.
(8) When transporting dirt, the vehicle must be driven at a moderate speed and at a slow speed, and no sharp turning or sudden braking should be allowed because the center of gravity of the anti-wave board is not high.
What product is suitable for book Gift Box Packaging:
Gift Box packaging, especially this kind of book gift box packaging, is mostly used for high-end gift packaging, such as liquor, jewelry and some health products. Similar to this type of product, book gift box packaging will be used Yes, but for the box type, it depends on what the customer likes.
The packaging material of the book-shaped gift box is basically not much different from the material of the ordinary gift box packaging. It also uses 157 grams of facial paper to mount 1200 grams of single white cardboard, but the book-shaped gift box packaging needs to be flipped. Therefore, a magnet will be added to the covered position, so the cost will be a bit more expensive than other types of gift boxes.
Shenzhen Rongdian Printing Products Co., Ltd. is located at 303, 3rd Floor, Building 2, Potoudu Industrial Zone, Longxi Village, Longcheng Street, Longgang District, Shenzhen, Guangdong Province, China. It mainly deals in various printing products: stickers, product color boxes, exquisite gift boxes, picture albums , Promotional color pages, trademark tags, envelope receipts! Shenzhen Rongdian Printing Products Co., Ltd. adheres to the production philosophy of "printing every product with heart" and strictly implements it! Looking forward to your visit~
Book-shaped gift box packaging customization, book-shaped gift box packaging manufacturer, book-shaped gift box packaging and printing
RONG DIAN PACKAGING & PRINTING CO.,LIMITED , https://www.rodiantpackaging.com